FOX AQUAFUGA FX150 Silicone-Enhanced Flexible Grout Material
FOX AQUAFUGA FX150 is a high-performance flexible grout material with a cement-based structure, water-repellent properties, and silicone-enhanced formula, providing resistance against mold and dirt formation. The product is safely used for grouting joints of covering materials such as tiles, ceramics, granite, natural stone, and marble. It delivers long-lasting grout performance without being affected by temperature variations, water exposure, or vibrations.
Complying with the TS EN 13888-1:2022 standard and classified as CG2WA, FOX AQUAFUGA FX150 is preferred for both residential applications and high-traffic areas thanks to its reduced water absorption and high abrasion resistance.
Where Is FOX AQUAFUGA FX150 Used?
FOX AQUAFUGA FX150 has a wide range of applications in both indoor and outdoor areas.
Application areas:
- Horizontal and vertical surfaces in indoor and outdoor environments
- Hotels, hospitals, shopping malls, and residential projects
- All wet areas
Surface Preparation
Before starting the grout application, the ceramic or tile adhesive must be allowed to achieve sufficient strength. Generally, a waiting period of 48 hours is adequate. Any remaining mortar residues in the joints must be removed, and the joint gaps should be completely opened. For highly absorbent materials, the joints must be moistened before applying the grout.
Mixing
The specified amount of clean water indicated on the packaging should be poured into a clean mixing container. FOX AQUAFUGA FX150 powder should be gradually added into the water while mixing with a drill mixer operating at 400–600 rpm for 2–3 minutes until a homogeneous consistency is achieved. After allowing the mixture to rest for 3–5 minutes, it should be mixed again for 1 minute before application.
Different water ratios or mixing methods may cause color variations.
Mixing ratios:
- For 20 kg: 6.40 ±0.20 liters of water
- For 5 kg: 1.60 ±0.05 liters of water
- For 1 kg: 320 ±10 ml of water
Application Method
The prepared mortar is applied into the joints using a rubber float with diagonal movements. In deep joints, the material should be allowed to settle, and the application should be repeated if necessary.
In extremely hot weather conditions and on absorbent surfaces, joints should be slightly moistened with a damp sponge before application. Once the material reaches sufficient hardness to withstand finger pressure, the surface should be cleaned with a wet sponge to achieve the final appearance.
Consumption
The consumption rate of FOX AQUAFUGA FX150 varies depending on ceramic dimensions, joint width, and joint depth. The consumption values provided in the technical data sheet are theoretical values and are expressed in g/m².
Advantages of FOX AQUAFUGA FX150
- Provides water-repellent properties and resistance against mold and dirt formation
- Easy to clean
- Resistant to impacts, vibrations, and detergents
- Resistant to freeze-thaw cycles
- Provides high abrasion resistance
- Bonds perfectly to ceramic edges without cracking
- Creates a smooth surface finish
- Easy to prepare and apply
- Does not scratch glazed surfaces
- Suitable for 2–8 mm joint widths
- Provides extended working time
- Does not fade or change color
Technical Specifications (Summary)
Material structure: Mineral fillers, synthetic additives, special polymers, and special silicone powders
Dry density: 1.10 ±0.05 kg/L
Fresh mortar density: 1.76 ±0.05 kg/L
Compressive strength: ≥15 N/mm²
Flexural strength: ≥2.5 N/mm²
Shrinkage: ≤3 mm/m
Abrasion resistance: ≤1000 mm³
Water absorption: ≤2 g (30 min), ≤5 g (240 min)
Application temperature: +5°C / +30°C
Service temperature: -20°C / +80°C
Maturation time: 3–5 minutes
Pot life: Approximately 60 minutes
Ready for use: 24 hours
Packaging, Storage, and Shelf Life
Packaging:
- 5 kg polyethylene bags
- 20 kg kraft bags
Shelf life: 12 months from the production date
Storage conditions: Store in a cool, dry, frost-free environment between +5°C and +30°C.
Safety Precautions
Application and storage areas should be properly ventilated. Protective clothing, gloves, safety glasses, and masks should be used during application.
The product should not come into contact with skin or eyes. In case of contact, wash thoroughly with plenty of water and soap. If swallowed, seek medical attention immediately.
Keep out of reach of children.
Frequently Asked Questions (FAQ)
Which joint widths can FOX AQUAFUGA FX150 be used for?
It is suitable for joint widths between 2–8 mm.
Is it suitable for wet areas?
Yes. It can be safely used in all wet areas.
Does it cause color fading?
No. It does not fade or change color.
How long after application can the surface be used?
The surface can generally be opened for use after approximately 24 hours.